Home > Xbox 360 > Reflow Xbox 360 With Heat Gun

Reflow Xbox 360 With Heat Gun

Contents

You can change this preference below. crazymodder2 39,931 views 11:15 Baking the Xbox 360, the SAFE way. - Duration: 8:27. Sign in to make your opinion count. I hadn’t turned on the system for months—it probably needed an update. weblink

I got this, I told myself. Working... On the top between the heatsink and motherboard you do need to use 2mm worth of washers. Then let the system sit for 30+ minutes.

Reflow Xbox 360 With Heat Gun

Here is a ranking of how well each fix does. 1 day fix reflow (Heat Gun; baking in oven at 275F for 2 hours will be more permanent) 1 month fix Alone. This video shows the least likely way of damaging a 360 for a beginer so I thought it was helpful video but I'm getting slammed by all the so-called self declared

What temperature should I use as a maximum to not go over? First let me explain these two seperate methods of repair: The Problem: As we all know by now, the Playstation 3 (PS3) can suffer from the dreaded Yellow Light of Death The small flathead screwdriver included with the kit is too small and weak to do the job. Reflow Xbox 360 With Hair Dryer Uploaded on 29 Jan 2010If you benefited from this video and use bitcoins, please consider donating any amount to 1GfMWhREmpYaYZELJ1ruyi3ymnSQqoomatThis is the method I use to reflow an xbox 360.

I even broke a few heating too fast and too quick. Reflow Xbox 360 Oven After heating the area boxed in red for four minutes, turn off your heat gun and allow the motherboard to cool down to room temperature without moving or disturbing it in I check the error codes they have and all of them say CPU/GPU overheat. Grasp the back portion of the lower case and lift it upwards to separate it from the console.

I will however use one of those pins for a ground. Reflow Xbox 360 Without Heat Gun For a constant 12v source I found that this mosfet looking chip is a good source. I used the washers that came off of the gpu heat sink when I took it off. So, I hooked the cables into the TV and tried again.

Reflow Xbox 360 Oven

This is assuming you have no distractions and you do it perfectly! Twist the screwdriver to fully release the X clamp from its retaining post. Reflow Xbox 360 With Heat Gun Add a comment Add a comment Add Comment 1024 Step 24 Edit Press the Xbox 360 opening tool down into the two remaining clips near the power connector. Xbox 360 Slim Reflow Ace M 336,829 views 15:40 How to heat up your GPU (reflow) without hurting your 360. - Duration: 4:25.

Lately, we've been getting a good number of customers coming to us telling us they received a reball repair, but in fact really just got a reflow. http://findthemes.net/xbox-360/how-to-play-original-xbox-games-on-xbox-360.html michiels - 07/05/2015 Reply Code 0013 I followed guide and it already has the rod fix kit and still two left red lights flash Andy Brown - 08/19/2015 Reply Is there Waste of time and money. Above the Memory Unit slots. Xbox 360 Reflow Temperature Profile

Might as well give that a shot, too. That’s when I noticed that this particular red light looked different than my old red ring. Next time I'm going to follow the settings (lo) and timings the PS3 guide suggests. check over here Throughout the following opening procedure, the finger of an Xbox 360 opening tool can be used in place of a spudger.

Spudgeboy - 03/10/2012 Reply Add a comment Add Comment 1024 Step 50 Edit With your heat gun set to HIGH, evenly heat the area boxed in red for four minutes. Xbox 360 Slim Heat Gun Reflow Use the flat end of a spudger to release the following latches: Above the front-facing USB ports. actually, maybe not.

I didn't heat the back for this.

This occurs due to a manufacturer's defect when creating the board and not accounting for the vast amounts of heat generated while playing with the system for long periods of time. Here is what happens to your XBox 360 when we receive it for repair at www.ohiocitysales.com Why risk your Xbox 360 when for the price of a guide or repair kit Their locations are highlighted in red. Xbox 360 Gpu Fix Lift the motherboard assembly from its front edge.

Add a comment Add a comment Add Comment 1024 Step 11 Top Vent Edit Stand the console vertically with the top edge facing up. Use the tip of your spudger to release the clip on the top vent nearest the back of the Xbox. lockemup555 262,914 views 4:25 Xbox 360 Ring Of Death How To Reset - Duration: 6:04. this content Now my repair kit is useless cause I physically removed some of the bits because my screwdriver slipped.